Differences

This shows you the differences between two versions of the page.

--- en:hems:methods_resources:wiring [2018/10/09 11:07] – goran.kocjancic
+++ en:hems:methods_resources:wiring [2021/03/19 12:13] (current) – neoxy
@@ Line 1: / Line 1: @@
 ====== HEMS G2 wiring ======
-===== SAFETY INSTRUCTION =====
-**Before start with installation, assembly, disassembly, inspection, or any other operation read safety instructions. They contain general safety information for devices approved by Robotina d.o.o..**
-{{:en:hems:methods_resources:warning.png?nolink|}} DANGER!
-**Disregard manufacturer's safety instructions could result in material damage, injury or even death.**
-{{:en:hems:methods_resources:el_warning.png?nolink|}} {{:en:hems:methods_resources:warning.png?nolink|}} DANGER!
-**During operation is device under load!**
-{{:en:hems:methods_resources:warning.png?nolink|}} WARNING!
-**Before installation, disassembly, inspection, or any other operation, make sure that the device is disconnected from the power supply and that with your doing you don’t endanger yourself or others.**
-{{:en:hems:methods_resources:warning.png?nolink|}} WARNING!
-**Don’t try to open the device.
-Any interference or change may impact device’s properties and significantly affect safety.**
-{{:en:hems:methods_resources:warning.png?nolink|}} WARNING!
-**Before connecting device to the power supply, assure that all wires are connected in accordance with the manufacturer's instructions.**
-Before continue with installation read the manufacturer's installation requirements:
-  * Installation and electrical connection of the equipment described in this manual must be carried out by qualified or authorized personnel.
-  * The device must be installed inside the electric box where cannot endanger people or environment.
-  * During the operation device must not be exposed to humidity, dust, mold or other weather phenomena.
-  * All connected wires must comply with manufacturer's specifications.
-  * For installation use only verified electrical-installations tools.
-  * Around the device has to be assured sufficient ventilation space.
-  * The manufacturer does not undertake any liability for material or personal damage resulting from use or handling which is not in accordance with the manufacturer's safety instructions.
 |< 700px >|
@@ Line 47: / Line 8: @@
 |< 700px >|
-^ PM-3-I-D                                                       |
+^ PM3-I-D                                                       |
 |  {{ :hiq_energy:hems:hardware:pm3_terminals.png?direct |}}     |
@@ Line 53: / Line 14: @@
 |< 700px >|
-^ PM-1-E-D                                                       |
+^ PM1-E-D                                                       |
 |  {{ :hiq_energy:hems:hardware:pm1_terminals.png?direct |}}     |
@@ Line 59: / Line 20: @@
 |< 700px >|
-^ PM-1-E-D-CT      |
+^ PM1-E-D-CT      |
 |  {{ :hiq_energy:hems:hardware:pm1_ct_terminals.png?direct |}}  |
-Example of HEMS G2 wiring diagram: {{ :hiq_energy:hems:methods_resources:hems_g2.pdf |}}
+<WRAP pagebreak></WRAP>
-Example done with [[https://www.3xm.se/|Elwin by 3xM]].
+|< 700px >|
+^ PM3-E-D-CT      |
+|  {{ :hiq_energy:hems:hardware:pm3_ct_terminals.png?direct |}}  |
+<WRAP pagebreak></WRAP>
+|< 700px >|
+^ Power-sensors orientation     |
+|  {{ :hiq_energy:hems:hardware:ps_orientation.png?direct |}}  |
-Archive file:{{ :hiq_energy:hems:methods_resources:20180924125415_hems_g2.zip |}}
-Custom library components: {{ :hiq_energy:hems:methods_resources:components.zip |}}