Differences

This shows you the differences between two versions of the page.

--- en:hems_v1_2_0:wiring [2021/11/12 08:33] – created saso_santelj
+++ en:hems_v1_2_0:wiring [2022/12/09 11:31] (current) – saso_santelj
@@ Line 15: / Line 15: @@
 |< 700px >|
-^ Network (LAN or LTE 4G modem) -> MC-230 and IOT-L2-2 \\ Optionally: \\  - PC with HEMS configurator \\  - PV inverter \\   - Hybrid inverter (battery storage system)   \\     - EV charger       |
+^ Network (LAN or LTE 4G modem) -> MC-230 and IOT-L2-2 \\ Optionally: \\  - PC with HEMS configurator \\  - PV inverter \\   - Hybrid inverter (battery storage system)   \\     - EV charger \\  \\ NOTE: When you change network configuration, MC-230 and IOT-L2-2 must be reset.      |
-|Default connection to the LAN:                              |
+|Default connection to the LAN network:                     |
 |  {{ :hiq_energy:hems_v1_2_0:hems-linker01.png?direct |}}  |
 |Optional LAN connections:                              |
 |  {{ :hiq_energy:hems_v1_2_0:hems-linker02.png?direct |}}  |
-|  {{ :hiq_energy:hems_v1_2_0:hems-linker03.png?direct |}}  |
+<WRAP pagebreak></WRAP>
-| |
+|< 700px >|
-| |
+| Default connection via LTE 4G modem:                            |
-|Default connection via LTE 4G modem:                            |
 |**NOTE:** All connected devices will have internet access via LTE modem which can result in high costs on your LTE account. |
 |  {{ :hiq_energy:hems_v1_2_0:hems-linker11.png?direct |}}  |
@@ Line 30: / Line 29: @@
 | |
 |**NOTE:** Specific network requirements, i.e. static IP address can be configured on the cloud service. Please contact [[http://support.robotina.com|support]]. |
 <WRAP pagebreak></WRAP>
@@ Line 37: / Line 35: @@
 ^ PM3-I-D                                                       |
 |  {{ :hiq_energy:hems:hardware:pm3_terminals.png?direct |}}     |
-<WRAP pagebreak></WRAP>
 |< 700px >|
@@ Line 49: / Line 45: @@
 ^ PM1-E-D-CT      |
 |  {{ :hiq_energy:hems:hardware:pm1_ct_terminals.png?direct |}}  |
-<WRAP pagebreak></WRAP>
 |< 700px >|
@@ Line 61: / Line 55: @@
 ^ WM-1      |
 |  {{ :hiq_energy:hems:hardware:wm1_wiring.png?direct |}}  |
-<WRAP pagebreak></WRAP>
 |< 700px >|
@@ Line 75: / Line 66: @@
 |Connect external source to control device, e.g. thermostat signal on IX0 to control temperature by enabling/disabling connected device on QX0.|
 |  {{ :hiq_energy:hems:hardware:water_heater_1.png?direct |}}  |
+<WRAP pagebreak></WRAP>
+|< 700px >|
+^ Set analog for consumer 1  |
+|Connect analog device to IO14 for analog signal 0-10V or to IO15 for PWM signal (f=1kHz). Analog load is possible to set in configurator for consumer 1 only and reserved outputs are on IO14 & IO15.|
+|  {{ :hiq_energy:hems:hardware:analog_1.png?direct |}}  |