Page locked

This page is currently locked for editing by another user. You have to wait until this user finishes editing or the lock expires.
Currently locked by: 114.119.159.76,10.0.0.202
Lock expires at: 2025/07/02 01:38 (8 min)
This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Commissioning ======

===== Control system =====

HEMS controller [[en:hiq_hw:hc-iq-hems|HC-IQ-HEMS]] and all communication interfaces are supplied with preinstalled firmware.

For system configuration use [[en:goflex_hems:software|HIQ HEMS Configurator]] .

===== Power meters =====

  - **Connect** only **one new power meter** at the time.
  - In **HIQ HEMS Configurator** go to **settings** page. New power-meter should be detected (Address and Type should be displayed).
  - Long-press button on power meter until **-SET-** is displayed.
  - Press **New address** and enter new address according to following table.

|<20% 60% >|
^  Device           ^  Address  |
| Grid              |  150      |
|                              ||
| 1st power plant   |  154      |
| 2nd power plant   |  155      |
| 3rd power plant   |  156      |
|                              ||
| 1st storage       |  157      |
| 2nd storage       |  158      |
|                              ||
| 1st consumer      |  160      |
| 2nd consumer      |  161      |
| ...               |  ...      |
| 8th consumer      |  167      |

===== Load managers =====

==== Add new device ====

  - In **HIQ HEMS Configurator** go to **wireless** page
  - **Click on device** which will be added
  - Wait for **network open - waiting device** status.
  - Press **button on device**.
  - Wait until device is addressed and configured.

Procedure can be interrupted with "**close network**" button.

==== Remove device ====

  - **Reset device**: 
    * power off wireless device for a few seconds. 
    * After powering on wait for a few seconds for device to boot on. 
    * Press and hold button, LED indicator will go **off**, then **green** and at the end **red**. 
    * Release button.
  - In **HIQ HEMS Configurator** go to **wireless** page
  - Reset device should have error state (yellow sign with exclamation)
  - Click on reset device to clear place.

===== Control devices =====

  - In **HIQ HEMS Configurator** go to **wireless** page
  - **Press icon** for control device (wireless enocean push-button) to be configured
  - On control device **press 0** (off) button
  - On control device **press 1** (on) button
===== Sensors =====

==== Add new sensor ====

  - Adjust sensor address with **DIP-switches** according following table
  - In **HIQ HEMS Configurator** click on sensor which will be added
  - Wait for **network open - waiting device** status
  - **Power on** and **pres button** on sensor
  - Wait until sensor is configured

Procedure can be interrupted with **“close network”** button.

|< 25% 25% 25% >|
^  Sensor  ^  Address  ^  DIP switch settings                                                                      |
|   S1     |   60      | {{ hiq_energy:goflex_hems:methods_resources:addr_60.png?nolink&100 |}}                      |
|   S2     |   61      | {{ hiq_energy:goflex_hems:methods_resources:addr_61.png?nolink&100 |}}                      |
|   S3     |   62      | {{ hiq_energy:goflex_hems:methods_resources:addr_62.png?nolink&100 |}}                      |
|   S4     |   63      | {{ hiq_energy:goflex_hems:methods_resources:addr_63.png?nolink&100 |}}                      |
|   S5     |   64      | {{ hiq_energy:goflex_hems:methods_resources:addr_64.png?nolink&100 |}}                      |
|   S6     |   65      | {{ hiq_energy:goflex_hems:methods_resources:addr_65.png?nolink&100 |}}                      |
|   S7     |   66      | {{ hiq_energy:goflex_hems:methods_resources:addr_66.png?nolink&100 |}}                      |
|   S8     |   67      | {{ hiq_energy:goflex_hems:methods_resources:addr_67.png?nolink&100 |}}                      |


==== Remove sensor ====

  - **Reset sensor**:
    * Power off sensor for few seconds
    * Reconnect sensor power supply
    * After sensor power on (but within 20 sec) press and hold button for at least 6 sec
  - In **HIQ HEMS Configurator** reset device should show error
  - **Click** on error icon **to free** occupied space