✎ en:sg3:configurator []

You've loaded an old revision of the document! If you save it, you will create a new version with this data.

====== Configurator ======

===== Overview =====

|< 475px  50px >|
^  1  ^ Page navigation                                                  |
| Overview page                                                         ||
| Access code management page                                           ||
| Settings page                                                         ||
| UI settings page                                                      ||
| Events overview page                                                  ||
^  2  ^ Entry procedure steps status                                     |
| [[en:sg3:configurator:count_status|]]                                 ||
| [[en:sg3:configurator:disinfect_status|]]                             ||
| [[en:sg3:configurator:temperature_status|]]                           ||
| [[en:sg3:configurator:code_status|]]                                  ||
| [[en:sg3:configurator:confirmation_status|]]                          ||
| [[en:sg3:configurator:entry_status|]]                                 ||
^  3  ^ [[en:sg3:configurator:schematics|]]                              |
^  4  ^ Occupation counts                                                |
| Occupation count, click to correct the actual number of visitors.     ||
| Occupation limits L1 / L2                                             ||
^  5  ^ Command buttons                                                  |
| Gates Auto / Manual mode toggle                                       ||
| Alarm reset button                                                    ||
| Confirmation button                                                   ||

</WRAP>

</WRAP>
<WRAP clear></WRAP>

===== Access Code management =====

|< 475px  50px >|
^  1  ^ Edited code                                                                                                     |
| Click to enter the code you want to edit.                                                                            ||
^  2  ^ Code type                                                                                                       |
| Click to select edited code type. Options ate L1 (level 1), L2 (level 2) or UL (unlimited).                          ||
^  3  ^ Access point limits                                                                                             |
| Click to enter count limits for each access point.                                                                   ||
^  4  ^ Code activation date                                                                                            |
| Set code activation date and time. Set all to 0 for the code that is active immediately.                             ||
^  8  ^ Code expiration date                                                                                            |
| Set code expiration date and time. Set all to 0 for a code that has no validity limit.                               ||
^  6  ^ Edit code commands                                                                                              |
| ''[ search ]'' = Find settings for "edit code".                                                                      ||
| ''[ save ]'' = Saves the code being edited with all settings.                                                      ||
| ''[ clear ]'' = Clear all edit settings.                                                                            ||
| ''[ delete ]'' = Delete edit code from the list.                                                                     ||
^  7  ^ Codes list                                                                                                      |
| List of access codes on the controller. Clicking on the code picks up all the code values in the edit fields above.  ||

</WRAP>

</WRAP>
<WRAP clear></WRAP>

===== Settings =====

|< 475px  50px >|
^  1   ^ Entry conditions                                                                                    |
| Count limits: set count limits for L1 and L2; 0=not limited                                               ||
| Disinfection: select if hand disinfection is required                                                     ||    
| Thermal scan: select if body temperature scan is required s                                               ||
| Reader: select if code reader is required                                                                 ||
| Confirmation: select if confirmation is required                                                          ||
^  2   ^ Entry detection settings                                                                            |
| Entry detection type: select entry detection type                                                         ||
| Entry time-out: max time between consecutive steps                                                        ||
| Confirmation time-out: max time allowed for confirmation                                                  ||
| Block time-out: time for hi temperature or wrong code alert                                               ||
| After all time-outs entry procedure restarts.                                                             ||
^  3   ^ Code reader settings                                                                                |
| Access point ID: ID for built in access point. Used when S Gate is part of bigger Access control system   ||
| Thermal scan timeout: set the time for which the system remembers the temperature scan for the code user  ||
| Access master code: set the code for local codes management                                               ||
| Send LAN code query: set to enable sending code queries to other access controllers on LAN                ||
| Process LAN code query: set to process queries from other controllers on LAN                              ||
^  4   ^ Auxiliary input settings                                                                            |
| AUX input type: set auxiliary input function to presence sensor or to call button                         ||
| Presence / Call time-out: aux function timeout                                                            ||
^  5   ^ Gates settings                                                                                      |
| Entry gate time-out: set entry gate signal timeout, 0=no entry gate                                       ||
| Exit gate time-out: set exit gate signal timeout, 0=no exit gate                                          ||
^  6   ^ Alarm settings                                                                                      |
| Alarm duration: alarm active duration time                                                                ||
| Alarm beeper enabled: set to enable continuous beep during alarm                                          ||
| Reset alarm on exit: set to reset alarm when exit is detected                                             ||
^  7   ^ Hardware overview                                                                                   |
| Control system overview                                                                                   ||
| Select ''[ Autodetect ]'' to find S Gate controller in LAN (when red Xes are displayed)                   ||
^  8   ^ Wireless devices management                                                                         |
| []wireless management: set to enable management of wireless devices                                       ||
| first icon: wireless device paired status (x=none, ✔=paired)                                              ||
| second icon: displaying wireless signal strength                                                          ||
| third icon: wireless device operating as repeater (click to enable).                                      ||
| ''[-]'': delete wireless device                                                                           ||
| ''[+]'': add wireless device                                                                              ||
^  9   ^ Controller date and time settings                                                                   |
| set S Gate controller date and time.                                                                      ||
^  10  ^ Parameters management                                                                               |
| ''[init parameters ]'': initialize all parameters to factory default values                               ||
| ''[save parameters ]'': save all parameters to permanent memory                                           ||
| ''[read parameters ]'': read all parameters from permanent memory                                         ||

</WRAP>

</WRAP>
<WRAP clear></WRAP>

===== User interfaces settings =====

|< 475px  50px >|
^  1  ^ LED display texts settings                                                                               |
| Click to set the texts displayed on the LED display. Edit text alignment with spaces.                         ||
^  1  ^ GUI display texts settings                                                                               |
| Click to set the texts that appear on the graphical user interface. The text will be centered automatically.  ||

</WRAP>

</WRAP>
<WRAP clear></WRAP>

===== Events overview =====

|< 475px  50px >|
^  1  ^ Events list                                                          |
| The last 20 event codes and data are displayed. Event #00 happened last.  ||
^  2  ^ Events legend                                                        |
| Legend for event code and data.                                           ||

</WRAP>

</WRAP>
<WRAP clear></WRAP>

Edit summary

Note: By editing this page you agree to license your content under the following license: CC Attribution-Share Alike 4.0 International